Course Specifications

Course Number:

093046

Course Length:

5 days

Course Description

Course Objectives:

In this course, you will implement scalable and highly secure Cisco routers that are connected to LANs, WANs, and IPv6 networking using advanced IP addressing and routing.

You will:

• Describe the fundamentals of network routing.
• Configure Layer 2 technologies.
• Configure IP addressing.
• Configure routes and route re-distribution.
• Configure routes.
• Configure RIPv2 and RIPng.
• Configure EIGRP.
• Configure OSPF and OSPFv3.
• Describe the fundamentals of Enterprise Internet connectivity.
• Configure BGP.
• Configure connectivity to remote locations.
• Configure device management and access control.
• Configure router security features.
• Configure network services.
• Configure NAT.
• Configure IP SLA and object tracking.
• Configure tracking interfaces and redundancy protocols.

Target Student:

This course is designed for network security specialists, security administrators, and network security support engineers who are responsible for deploying and managing Cisco routing products and features in a network infrastructure. Individuals should attend if their primary job responsibility is to handle and secure the routing configuration of their organization's network.

This course is also designed for students who are seeking Cisco CCNP and CCDP certifications and who want to prepare for Implementing Cisco IP Routing (ROUTE) Exam 300-101.

Prerequisites:

To ensure your success in this course, you should have experience with basic networking and security and routing concepts, and Cisco IOS networking features and concepts. You can obtain this level of skills and knowledge by taking the following courses, available from Logical Operations:

• CompTIA® Network+® (Exam N10-006)
• Cisco® CCENT®/CCNA® 3.0: Interconnecting Cisco Network Devices, Part 1 (ICND1)
• Cisco® CCNA® 3.0: Interconnecting Cisco Network Devices, Part 2 (ICND2)

Course-specific Technical Requirements

Hardware and Software:

You will need the following hardware and software configurations.

NYEDGE1

• Cisco 2911 Router
• 1 * HWIC-2T module
• c2900-universalk9-mz.SPA.152-4.M6.bin
• Licenses: Data and Security

NYEDGE2

• Cisco 2911 Router
• 1 * HWIC-2T module
• c2900-universalk9-mz.SPA.152-4.M6.bin
• Licenses: Data and Security

NYWAN1

• Cisco 2911 Router
• 1 * HWIC-2T module
• 1 * HWIC-1T module
• c2900-universalk9-mz.SPA.152-4.M6.bin
• Licenses: Security and Voice

NYCORE1

• Cisco 3750v2-24PS or Cisco 3750v1-24PS Switch
• 3750v2: 15.0 IPServicesK9
• 3750v1: 12.2 Advanced IP Services

NYCORE2

• Cisco 3750v2-24PS or Cisco 3750v1-24PS Switch
• 3750v2: c3750-ipservicesk9-mz.150-2.SE2
• 3750v1: c3750-ipservicesk9-mz.122-55.SE5

NYACCESS1

• Cisco 2960-24TC-S Switch
• c2960-lanlitek9-mz.150-2.SE9.bin or c2960-lanlitek9-mz.122-55.SE5.bin

Cisco Phone

• Any Cisco IP POE phone will work
• Either SIP or SCCP software

Backend (BGP)

• 2 Cisco 2800 series routers
• 1 * WIC-2T module
• 2 * Cisco 2811 routers running enterprise software. These routers need to run BGP and Frame Relay services

You will also require a computer or laptop for the PLABCSCO01 device with the following minimum hardware and software configurations:

• Processor (CPU): Intel Core i3-3xxx or equivalent - Microsoft Windows 7 Professional, Enterprise, or Ultimate
• Memory: 4 GB RAM - Internet Explorer 11 or above
• Storage: 500 GB internal hard drive - PuTTY (http://www.putty.org/)
• NIC - IP Address 192.168.16.10/24, GW .1 - Tftpd32 (http://tftpd32.jounin.net/)
• Display card that runs at 1280 x 1024 or higher display resolution, and a compatible display monitor - FileZilla (https://filezilla-project.org/)
• Internet access (contact your local network administrator) - 7ZIP (http://www.7-zip.org)
• Keyboard and mouse

Accessories:

You will require the following cables for the setup:

• 5 straight-through cables.
• 4 crossover cables.
• 1 Cisco console cable. You may need a USB-to-serial adapter if your PC/laptop does not have a serial port.
• 5 Cisco serial DCE/DTE cables.

Course Content

Lesson 1: Overview of Network Routing

 Topic A: The Role of Dynamic Routing Protocols

 Topic B: Overview of Network Operations

 Topic C: Overview of General Network Challenges

Lesson 2: Introduction to Layer 2 Technologies

 Topic A: Configure PPP and PPPoE

 Topic B: Overview of Frame Relay

Lesson 3: Configuring IP Addressing

 Topic A: Configure IPv4 Addressing and ARP

 Topic B: Configure DHCP Relay

 Topic C: Overview of IPv6 Addressing and DHCP

Lesson 4: Configuring Routes and Route Redistribution

 Topic A: Configure Routes

 Topic B: Redistribute Routes

 Topic C: Control and Manipulate Redistribution

Lesson 5: Configuring Routes

 Topic A: Configure EIGRP Routes

 Topic B: Configure OSPF Routes

 Topic C: Configure Policy-Based Routing

Lesson 6: Configuring Routing Information Protocols

 Topic A: Overview of RIP

 Topic B: Configure RIPng

Lesson 7: Configuring EIGRP

 Topic A: Configure EIGRP Neighbor Relationship and Authentication

 Topic B: Configure EIGRP Stubs

 Topic C: Configure EIGRP Load Balancing and Metrics

 Topic D: Configure EIGRP for IPv6

Lesson 8: Configuring OSPF and OSPFv3

 Topic A: Configure OSPF

 Topic B: Overview of OSPF Route Summarization

 Topic C: Configure OSPFv3

Lesson 9: Introduction to Enterprise Internet Connectivity

 Topic A: Overview of Single-Homed Internet Connectivity

 Topic B: Overview of Dual-Homed and Multi-Homed Internet Connectivity

Lesson 10: Configuring BGP

 Topic A: Overview of BGP

 Topic B: Configure iBGP

 Topic C: Configure eBGP and Route Filtering

 Topic D: Configure BGP for IPv6

 Topic E: Configure Route Filtering Using Prefix Lists

Lesson 11: Configuring Connectivity to Remote Locations

 Topic A: Configure a GRE Tunnel

 Topic B: Encrypt Data Using IPsec

Lesson 12: Configuring Device Management and Access Control

 Topic A: Overview of AAA

 Topic B: Configure Device Access Control

Lesson 13: Configuring Router Security Features

 Topic A: Overview of Router Security

 Topic B: Configure IPv4 Security

Lesson 14: Configuring Network Services

 Topic A: Configure DHCP

 Topic B: Configure Time Synchronization Using NTP

 Topic C: Configure Logging

 Topic D: Configure SNMP

Lesson 15: Configuring NAT

 Topic A: Configure the NAT Virtual Interface

 Topic B: Overview of NAT64 and NPTv6

Lesson 16: Configuring IP SLA and Object Tracking

 Topic A: Configure IP Service Level Agreements

 Topic B: Configure Object Tracking with IP SLA

Lesson 17: Configuring Tracking Interfaces and Redundancy Protocols

 Topic A: Configure Tracking Interfaces

 Topic B: Configure Tracking and Redundancy Protocols